We appreciate the contributions many of you have been able to make towards repairing the storm damage and keeping a roof over our heads. With your help we’ve been able to complete much of the critical work. There is still work to be done to secure the house and your continued support will be a huge help.
Guests have read-only access to our forums. If you wish to participate you will need to register. Be sure to activate your account from the email sent to you when you register.
I installed Windows 11 23H2 recently and want to use SDIO 1.12.22.763 to install drivers. However when I opened the SDIO software and went to download driver Pages, It pop up an error immediately when I clicked any one of the three buttons:
Exception: std::bad_cast The program will self terminate now.
Later on, The entire program crashes.
I sincerely hope you can solve this problem, Thank you!
please post the log
Here is part of the log. Main error is "ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small":
```
.............
Windows v11.0.22631
START 1,0 [15]
Windows v11.0.22631
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'RTL8168H.ndi.NT'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'iCFL_w10_DS'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'Install_GEN_PSR_JfP1_9462_AC_no_160_1x1'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'IntcAudModel'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'ibtusb'
Marker: 'Dell_nb'
FINISH primary
{Sync...
}Sync
{2Sync
Times
devicescan: 2313 (5 errors)
indexes: 0
sysinfo: 31
matcher: 15
chkupdate: 0
startup: 2359 (0)
indexsave: 0
indexprint: 0
total: 2359
test: 2328
Driverpacks
0 drivers\unpacked.7z
Sum: 0
Windows
Version: Windows 11 (11.0.22631)
PlatformId: 2
Update:
ServicePack: 0.0
SuiteMask: 256
ProductType: 1
Environment
windir: C:\WINDOWS\inf\
temp: C:\Users\DELL\AppData\Local\Temp
..................
```
Full log file is attached.
Here is part of the log. Main error is "ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small":
```
.............
Windows v11.0.22631
START 1,0 [15]
Windows v11.0.22631
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'RTL8168H.ndi.NT'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'iCFL_w10_DS'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'Install_GEN_PSR_JfP1_9462_AC_no_160_1x1'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'IntcAudModel'
ERROR with unicode2ansi():[7a]'The data area passed to a system call is too small.
'
ERROR: sect not found 'ibtusb'
Marker: 'Dell_nb'
FINISH primary
{Sync...
}Sync
{2Sync
Times
devicescan: 2313 (5 errors)
indexes: 0
sysinfo: 31
matcher: 15
chkupdate: 0
startup: 2359 (0)
indexsave: 0
indexprint: 0
total: 2359
test: 2328
Driverpacks
0 drivers\unpacked.7z
Sum: 0
Windows
Version: Windows 11 (11.0.22631)
PlatformId: 2
Update:
ServicePack: 0.0
SuiteMask: 256
ProductType: 1
Environment
windir: C:\WINDOWS\inf\
temp: C:\Users\DELL\AppData\Local\Temp
..................
```
Full log file is not allowed to attach here.
I'll have a look.
I also have the same problem, but on Windows 7. It worked fine before. The previous version I used was v1.12.20 (R761). I got this problem after the update.
to which three buttons do you refer? I don't see that error anywhere in the log snippet you posted. Perhaps you can post the complete log?I installed Windows 11 23H2 recently and want to use SDIO 1.12.22.763 to install drivers. However when I opened the SDIO software and went to download driver Pages, It pop up an error immediately when I clicked any one of the three buttons:
Exception: std::bad_cast The program will self terminate now.
Later on, The entire program crashes.
I sincerely hope you can solve this problem, Thank you!
Not sure why I can't attach file here.
So I upload it <a href=" removed link " target="_blank" rel="noopener">here.
It says file type is not allowed.
mediafire[]com/file/retg6x4we770al7
Yes.. There's 2 type of files in logs folder, .txt and .snp.. so i put it in a .rar
I can't even attach .txt file here so I upload it to Mediafire..
ohh I get it 🙂 So i can see a single error which is:
Torrent: http://www.snappy-driver-installer.org/downloads/Drivers.torrent
Waiting for torrent...............................DONE
Latest Version: Not found.
Updated driver packs available: 16
torrent_resume
{torrent_start
ERROR: Exception: std::bad_cast
}stop loggingHere is my screenshots and logs (Because the page is too limited, I uploaded the two files on Github.)
Screenshots:github[]com/265785/265785/assets/56037874/9e81e140-d6a8-4a43-8db4-daf1238ab1a4
Logs:github[]com/265785/265785/files/15177905/logs[]zip
The page is too limited. I tried many times to upload the picture and logs, but they are all removed by the page. Thank you! @levianth
